Before I take this out. I can't seem to find any replacement part. Anyone got one?? I might just buy a whole new motor. Might be easier and cheaper. Ughhhh
M
Search found 11 matches
- Mon Mar 21, 2016 11:14 pm
- Forum: Technical Discussion
- Topic: Broken shaft advancer
- Replies: 4
- Views: 4805
- Mon Mar 21, 2016 10:53 pm
- Forum: Bikes
- Topic: 1980 cb650 parts -complete bike
- Replies: 5
- Views: 22727
Re: 1980 cb650 parts -complete bike
Need the shaft advancer and pulse generator and all the nuts and bolts too.....let me know how much.
Much app
Much app
- Tue Mar 15, 2016 4:09 am
- Forum: Technical Discussion
- Topic: Broken shaft advancer
- Replies: 4
- Views: 4805
Re: Broken shaft advancer
I meant to can't use the 10mm nut to hold it while I crank other way.
- Tue Mar 15, 2016 4:07 am
- Forum: Technical Discussion
- Topic: Broken shaft advancer
- Replies: 4
- Views: 4805
Broken shaft advancer
Any ideas how to remove a broken shaft advancer? If I can use the 10mm nut to hold it in place?
Thanks M
Thanks M
- Tue Mar 15, 2016 4:01 am
- Forum: Technical Discussion
- Topic: Starter...bike won't start....
- Replies: 7
- Views: 6334
Re: Starter...bike won't start....
So how do I hold this shafts advancers if the threads to the nut is broken? ?
- Mon Mar 14, 2016 12:46 pm
- Forum: Technical Discussion
- Topic: Starter...bike won't start....
- Replies: 7
- Views: 6334
Re: Starter...bike won't start....
:D :D Update. Engine was sized. Used acetone and atf mix to unfreeze after a week of siting Pretty rusty inside the combustion chamber. I'm going put seafoam next to clean up the carbon deposit. So now new problem while I was gone on vacation my dad tried his hand at the seed motor by turning the nu...
- Mon Mar 14, 2016 12:36 pm
- Forum: Technical Discussion
- Topic: Air filter pods
- Replies: 9
- Views: 13281
Re: Air filter pods
I'm not sure what pod filters your using bit I use Uni pod filters and I have no need to reject. I use the uni stage 2 filter. The problem with open air flow pods like velocity stacks is the need for reject and retuning these uni basically mimic the air flow the original airbox has. I've used these ...
- Thu Feb 25, 2016 1:19 pm
- Forum: Technical Discussion
- Topic: Starter...bike won't start....
- Replies: 7
- Views: 6334
Re: Starter...bike won't start....
I'm using one of car booster packs I use it to start my cb900f. I connected it directly to the fat wire on the starter and still no go. So I've bypassed the solenoid all together. The brushes on the starter are in spec. I've cleaned up all the carbon. I put my finger in hole where the starter goes I...
- Thu Feb 25, 2016 2:56 am
- Forum: Technical Discussion
- Topic: Starter...bike won't start....
- Replies: 7
- Views: 6334
Starter...bike won't start....
:?: :?: :?: So I got this bike with unknown history. Before I cleaned the carbs I checked the oil. Then I blew in a bit of gas into the intake ports and it fired up for a sec. Compression is good I forget the numbers but it was well in range. Anyways fast forward to now. I had a problem with the neu...
- Thu Feb 25, 2016 2:41 am
- Forum: Technical Discussion
- Topic: Neutral Switch on Left crankcase
- Replies: 2
- Views: 3443
Re: Neutral Switch on Left crankcase
Okay it's fixed. The metal tongue attached to the roller was pushed down to far to make contact. So I took it out and pry'd it up then as I screwed it in I moved as close as I could. Now it contacts. Green light for all!!! Now the next problem. My starter...... I'll start a new thread for that. Than...
- Mon Feb 22, 2016 7:25 am
- Forum: Technical Discussion
- Topic: Neutral Switch on Left crankcase
- Replies: 2
- Views: 3443
Neutral Switch on Left crankcase
Hello Everyone!! From Raincouver BC!! Thanks for inviting me ot your board, great place lots of knowledge and interesting posts to read! History of my CB650. i bought it not running with a salvage title. Previous owner had it for 3 years and never ran it. I checked compression 110+, the starter work...