Do you have a pic of your old tank, I have 2 cb650 gas tanks, different years
Sent from my SM-G955U using Tapatalk
Search found 29 matches
- Sat Oct 23, 2021 8:33 pm
- Forum: General Discussion
- Topic: 1981 CB650 gas tank
- Replies: 2
- Views: 10531
- Sat Feb 20, 2021 12:57 am
- Forum: Accessories and Apparel
- Topic: Dyna S for the 650
- Replies: 2
- Views: 9392
Re: Dyna S for the 650
Can this be used in place of those square boxes under the seat that short out
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
- Fri Sep 25, 2020 12:39 pm
- Forum: Technical Discussion
- Topic: 1980 cb650 ignition system
- Replies: 5
- Views: 11032
Re: 1980 cb650 ignition system
What are the pulsator coils
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
- Thu Sep 24, 2020 10:00 am
- Forum: Technical Discussion
- Topic: 1980 cb650 ignition system
- Replies: 5
- Views: 11032
Re: 1980 cb650 ignition system
Yeah, I just do not want the factory electronic ignition, it is getting harder to find parts
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
- Fri Sep 11, 2020 11:30 pm
- Forum: Technical Discussion
- Topic: Press in jet size? Only runs with choke open
- Replies: 5
- Views: 10269
Re: Press in jet size? Only runs with choke open
Putting the cart before the horse but, when you get done, this tool is only 25 bucks on ebay and will allow you to sync carbs
https://m.youtube.com/watch?v=nh4OqKzuRvk&t=397s
Sent from my SM-G955U using Tapatalk
https://m.youtube.com/watch?v=nh4OqKzuRvk&t=397s
Sent from my SM-G955U using Tapatalk
- Fri Sep 11, 2020 11:24 pm
- Forum: Technical Discussion
- Topic: 1980 cb650 ignition system
- Replies: 5
- Views: 11032
1980 cb650 ignition system
1) can I use stock ignition without ignitor boxes
2) if not, can I use points setup from a cb550?
Sent from my SM-G955U using Tapatalk
2) if not, can I use points setup from a cb550?
Sent from my SM-G955U using Tapatalk
- Fri Mar 20, 2020 6:03 pm
- Forum: General Discussion
- Topic: Clutch/stator puller
- Replies: 3
- Views: 14537
Re: RE: Re: Clutch/stator puller
Hi, do you mean for removing the rotor on the left side of the engine? I've never needed one to remove a clutch. Have a look at this to see if its any help. http://www.hondacb650.com/viewtopic.php?f=4&t=15055&p=96064&hilit=puller#p96064 Thanks, yes the rotor assembly I guess Sent from m...
- Mon Mar 16, 2020 9:33 pm
- Forum: General Discussion
- Topic: Clutch/stator puller
- Replies: 3
- Views: 14537
Clutch/stator puller
Will acb550 clutch hub puller work on a 1980 cb650
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
- Wed Apr 03, 2019 2:03 pm
- Forum: General Discussion
- Topic: My New(someone’s old)1980 cb650
- Replies: 5
- Views: 14861
Re: My New(someone’s old)1980 cb650
Where are you located, i have a 1980 that could be a good parts bike, 250 takes it
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
- Sat Nov 24, 2018 7:57 am
- Forum: General Discussion
- Topic: CBX 650 E parts?
- Replies: 10
- Views: 10289
Re: CBX 650 E parts?
Check your floats, pour some gas in a can or bowl. Take floats out of carbs, place them one at a time in the gas. Wait 5 minutes, see if they sink. If one or all sink, they have a hole
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
- Sat Nov 24, 2018 3:21 am
- Forum: General Discussion
- Topic: CBX 650 E parts?
- Replies: 10
- Views: 10289
Re: CBX 650 E parts?
If your float needles are not sealing, a good fix is this. Remove carbs, set on table upside down, remove bowls, remove floats and needles, take a q-tip and cut 1 end off and put in drill, apply a small amount of toothpaste to q-tip and polish brass seat. Take a clean q-tip and run it through after....
- Sat Nov 10, 2018 7:41 am
- Forum: General Discussion
- Topic: Left hand high/low beam,indercater assembly
- Replies: 11
- Views: 21901
Re: Left hand high/low beam,indercater assembly
PayPal is good. I need a mailing address.
Hiwaybikertrash@yahoo.com is my PayPal
Sent from my SM-G955U using Tapatalk
Hiwaybikertrash@yahoo.com is my PayPal
Sent from my SM-G955U using Tapatalk
- Tue Nov 06, 2018 6:56 am
- Forum: General Discussion
- Topic: Left hand high/low beam,indercater assembly
- Replies: 11
- Views: 21901
Re: Left hand high/low beam,indercater assembly
30 bucks too much? If you are in the 48 states, I'll pay shipping
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
- Mon Nov 05, 2018 7:30 am
- Forum: General Discussion
- Topic: Left hand high/low beam,indercater assembly
- Replies: 11
- Views: 21901
Re: Left hand high/low beam,indercater assembly
Thanks, I can do that tonite. I know my Harley the wiring runs through the bars
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
- Sun Nov 04, 2018 10:25 pm
- Forum: General Discussion
- Topic: Left hand high/low beam,indercater assembly
- Replies: 11
- Views: 21901
Re: Left hand high/low beam,indercater assembly
Ok, I did not look close at it, do the wires through the bars? Do you need the wiring, is it easy to remove it?
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk