Sorry for the delayed response but I was able to locate one on ebay by messaging sellers of Honda CB parts directly to see if they had any guides left in their parts bikes that they had not yet listed.
Thank you still George.
Search found 11 matches
- Sat Feb 09, 2019 12:19 am
- Forum: Technical Discussion
- Topic: Cam Chain Guide 1981 CB650
- Replies: 10
- Views: 5608
- Thu Jan 24, 2019 2:35 pm
- Forum: Technical Discussion
- Topic: Cam Chain Guide 1981 CB650
- Replies: 10
- Views: 5608
Re: Cam Chain Guide 1981 CB650
Hi Dom, Partzilla has the one in your pic listed for 500 and 550 fours. The spare one I have was from a parts engine and TBH its pretty knackered. The one in your pic looks to have one square mounting point where the one in my pic are both round. tensioner blade 002.JPG George, I would still be int...
- Thu Jan 24, 2019 8:19 am
- Forum: Technical Discussion
- Topic: Cam Chain Guide 1981 CB650
- Replies: 10
- Views: 5608
Re: Cam Chain Guide 1981 CB650
Where are you Dom? Ebay should have some listed although the prices seem to vary wildly. I do have one but I don't think it was in a very good shape, it's been a while since I've seen it, I'll check it out later. I am located out of Connecticut. Ebay has many listed for the CB550 but these aren't c...
- Wed Jan 23, 2019 3:13 pm
- Forum: Technical Discussion
- Topic: Cam Chain Guide 1981 CB650
- Replies: 10
- Views: 5608
Cam Chain Guide 1981 CB650
During my current teardown I have observed the cam chain guide at the front/header side of the motor has snapped right in half! I am having a very difficult time finding a replacement. Any help is appreciated, if anyone is willing to part with a halfway decent spare, that would be tremendous. . PN: ...
- Tue Nov 25, 2014 12:10 pm
- Forum: Technical Discussion
- Topic: Need A Starter Clutch
- Replies: 3
- Views: 3064
Re: Need A Starter Clutch
Thank you! That should work for the internal components of the clutch. I'm hung up on whether to replace the actual clutch itself. What are the typical signs that of it needing to be replaced? The body of it has shifted so only one of the three torx bolts was able to fall out of place. With the othe...
- Tue Nov 25, 2014 2:38 am
- Forum: Technical Discussion
- Topic: Need A Starter Clutch
- Replies: 3
- Views: 3064
Need A Starter Clutch
Just went through the task of removing my faulty starter clutch for my 1981 cb650 and im having a hard time locating a replacement. Anyone have any suggestions on places I could get my hands on a new one? Do clutches from the cb750's work? I'm looking at one for sale on ebay and it looks slightly di...
- Sun Jun 22, 2014 11:49 am
- Forum: Technical Discussion
- Topic: 1981 Honda CB650 charging issues
- Replies: 2
- Views: 2392
Re: 1981 Honda CB650 charging issues
Tried it, battery began charging.
Thanks for the input, time to hunt around for some R/R units
Thanks for the input, time to hunt around for some R/R units
- Tue Jun 17, 2014 8:02 pm
- Forum: Technical Discussion
- Topic: 1981 Honda CB650 charging issues
- Replies: 2
- Views: 2392
1981 Honda CB650 charging issues
My system isn't charging the battery. I did the following checks. checked resistance between rotor rings and got 4.6 ohms checked for continuity in the yellow stator output leads between each other and the earth. Passed all tests. checked the rectifier and got big resistances from the green to yello...
- Wed May 28, 2014 7:27 pm
- Forum: Technical Discussion
- Topic: Still need a little help....spark or fuel?
- Replies: 11
- Views: 5872
Re: Still need a little help....spark or fuel?
I have almost the exact same problem with my bike, it can't rev up high with a load on it. How can you make it run on a less rich mixture?
- Wed May 28, 2014 12:09 am
- Forum: Technical Discussion
- Topic: 1981 Honda CB650 only firing on cylinders 1 and 2
- Replies: 3
- Views: 2651
Re: 1981 Honda CB650 only firing on cylinders 1 and 2
thanks for the insight, I actually have it running on all 4 now. Low end power is good but I couldnt get it to push past around 50 mph. Probably gonna need to go through the carbs again. Maybe they're out of sync or a high speed jet is clogged.
- Mon May 26, 2014 12:53 am
- Forum: Technical Discussion
- Topic: 1981 Honda CB650 only firing on cylinders 1 and 2
- Replies: 3
- Views: 2651
1981 Honda CB650 only firing on cylinders 1 and 2
Hello all, new to the forum and new to motorcycles. Just picked up this bike a short while ago that had sat for a while with the carbs off the bike. I reassembled it and the bike is only firing on cylinders 1 and 2. All the carburetor bowls are receiving gas and their seems to be solid spark and com...